Minecraft в Minecraft'e

https://invidious.privacyredirect.com/watch?v=GwHBaSySHmo

Думаю, никому не нужно объяснять, что такое Minecraft. Простая, на первый взгляд, игра таит в себе огромные возможности. Особенно преуспели фанаты игры в строительстве различных механизмов. Был собран и калькулятор, и даже полноценный программируемый компьютер. Обсуждение таких машин непременно сопровождается комментариями вида:
Теперь надо собрать эмулятор PC в майнкрафтеИ в нём запустить майнкрафтЖдем когда в minecraft реализуют сам minecraft
Поздравляю, господа, дождались! В майнкрафте реализовали сам майнкрафт.
Читать дальше →

Building an 8-Bit Computer – Now With Instructions

I have been thinking about doing an Instrucables article on my computer project for a while now as the goal of this project being on the internet in the first place is to help people with a similar goal. For those of you who are not familiar with Instructables, it is a comprehensive DIY website written by makers from all corners of life. All it takes to write a how-to article is to register for an account and share what you do. I finally got around to writing my article on how to build an 8-bit computer from scratch. It took me three days...

Test Time

I just finished wiring up the NVRAM chips to the computer. They are being addressed by a 8-bit program counter separate from the computer’s control counter. The control matrix changes its control word on the falling edge of the clock pulse. This allows the control to set up the 16-bit word, needed to tell which registers or operations are to be active, for the rising clock pulse.

There are a few problems, however, that have made this a bit more difficult than it should be. Since the NVRAM chips I am using are CMOS driven, the TTL chips do not always...

NVRAM Programmer

For the control matrix of my computer I am using some NVRAM chips to store a 16-bit control word for the various registers and control wires of my CPU. I decided not to use EEPROM as the chips that I bought were all faulty and wouldn’t write (I consulted many people and they agreed). I also decided that moving breadboard wires around was an extremely inefficient way to program 70 control words at 70 addresses. Which is why I decided to create a simple NVRAM (or EEPROM) programmer using the Arduino to send out addresses and data as well as control the...

Microinstructions Done

I finished the microinstructions for the control matrix of my computer. The block diagram on the upper left is the architecture of the computer itself. The chart below it is a list of OP codes for different macroinstructions. The chart on the right is the list of each individual microinstruction that makes up each macroinstruction.

For sake of simplicity I’ve also put all of this data into an excel worksheet that reads out base-10 numbers to make programming the NVRAM easy if I choose to use my Arduino for a programmer.

The Bulk of My Computer

After a month I finally received my breadboards from China and can start finishing the breadboard work on my computer. I now have all of the registers constructed as well as the ALU. Everything is connected to a data bus (bottom) that allows for the transfer of data from one register on the computer to another. All that remains now is the control matrix as well as the logic that drives the operation of the computer (run/stop, manual clock, auto, etc…). All of the yellow wires are control bits for the registers.

The Bulk of My Computer

Control Matrix Programming

A CPU consists mainly of registers (places to store values) that have to be controlled by, you guessed it, a control matrix. The control matrix outputs a control word, CON, whose bits activate the needed registers on a computer for input and output. For my computer I am using 3 NVRAM chips to store all of the control words.

The control matrix on my computer has two stages, both of wich consist of 3 steps. The entire sequence is called the machine cycle. And, in my computer’s case, the machine cycle also is equivalent to the instruction cycle which is how...

The Display

For the display I wanted something more interesting than a simple binary readout. I decided to go with the retro look and use some IV-9 russian Numitron tubes that can be conveniently driven by 5V with 20mA of current, the perfect amount to use a 4511 7-segment decoder. The only problem in the way of a steampunk output for my computer was converting the base-16 output of my computer into 3 digits of base-10 binary coded decimals.

Binary coded decimals are exactly what they sound like. The BCD system uses binary values 0-9 to express the base-10 digits that we use...

Two Useful Books

Without the textbook Digital Computer Electronics by Albert Malvino I wouldn’t have been able to even start this project. If you are considering building, or even learning about a computer using TTL this book is extremely worth the small amount of money you have to pay for it on Amazon. The TTL Cookbook by Don Lancaster is also extremely useful and provides pinouts for most of the 7400 series TTL chips that you would need for such a project.

The Golden Book

The 7400 Dictionary

First Parts

The first parts that I purchased for my computer included two breadboards and the logic chips to build a simple Arithmetic Logic Unit that could preform addition and subtraction on 4 bits. Initially I was going to build a 4 bit computer, but I later decided that having a computer that could only operate with integers from 0 to 15 would be rather boring. I learned something very important with my first purchase: NTE chips are not meant for projects. NTE chips are fairly common if you are searching for cheap parts, and the reason behind that is that they...